Ошибка
- Войдите на сайт для отправки комментариев
Вс, 31/07/2016 - 18:59
Здравствуйте, ардуино выдает такую ошибку, что это значит.
avrdude: Version 6.3, compiled on Jun 22 2016 at 16:05:21
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM7
Using Programmer : arduino
Overriding Baud Rate : 115200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 2
Firmware Version: 1.16
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: reading input file "C:\Users\Anton\AppData\Local\Temp\buildc4e990265812c8067a1c955fa4dc3c92.tmp/eeprom_clear.ino.hex"
avrdude: writing flash (764 bytes):
Writing | ################################################## | 100% 0.15s
avrdude: 764 bytes of flash written
avrdude: verifying flash memory against C:\Users\Anton\AppData\Local\Temp\buildc4e990265812c8067a1c955fa4dc3c92.tmp/eeprom_clear.ino.hex:
avrdude: load data flash data from input file C:\Users\Anton\AppData\Local\Temp\buildc4e990265812c8067a1c955fa4dc3c92.tmp/eeprom_clear.ino.hex:
avrdude: input file C:\Users\Anton\AppData\Local\Temp\buildc4e990265812c8067a1c955fa4dc3c92.tmp/eeprom_clear.ino.hex contains 764 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 0.10s
avrdude: verifying ...
avrdude: 764 bytes of flash verified
avrdude done. Thank you
А ошибка-то где?
А ошибка-то где?
Да я уже понял, бред написал)). До этого скетч не загружался, я поменял порт, выдавало ошибку, хотя до этого запускал нормально, потом перезпустил прогу, начало показывать такое сообщения и с другого скетча запустил погас экран. Ну я и подумал что то то не так.